DRAGON DROP DECK CONTAINER Drop | Step Deck Trailers For Sale

Details

General Specs

DRAGON 60 x 102 Drop | Step Deck Trailers

Drop | Step Deck Trailers

Beaumont TX USA


General Specs

DROP DECK CONTAINER

New

60 ft

102 in

41.0 in

NOT SPECIFIED


Body, Door, and Floor Specs

NOT SPECIFIED


Detailed Description

Axle Removable Neck Heavy Haul Trailer

Specifications:
• Type: Low Profile Flat Bed with removable neck.
• Payload: 60 tons (120,000 lb) distributed over 16 ft.
• Overall length: 59’ – 8”
• Deck length: 45’ – 0”
• Deck width: 8’ – 6” (102”)
• Deck height: 3’ – 5” (41”)

60 Ton 4 Axle Heavy Haul Trailer
• Deck Camber: 2" nominal, neck to tail.
• King Pin Settings: 16” and 34”
• Swing Clearance: 8’ – 6” (102”) and 10’ – 0” (120”).
• Frame: 4 beam design. Fabricated beams from a A514 T-1 high tensile
steel flanges and webs. Main beams boxed reinforced at critical deck
transition, 2-1 minimum safety factor at maximum payload stresses.
• Front Deck: 22'-8" L, 2" apitong attached at ends and every other cross
member.
• Rear Deck: 22' -4" L including tail roller, 1/4" steel plate deck,
continuous welds on top, intermittent welds on under side.
• Neck: Mechanical removable with roller at rear, 2 King Pin locations,
spare tire carrier each side.
• Rear Deck Roller: 8" SCH 160 pipe (8 5/8" OD) with double spherical
bearings, 2 sets of over load rollers, grease fittings on main roller and
overload rollers.
• Neck Roller: 6" SCH 160 pipe (6-5/8" OD) with double spherical
bearings, grease fittings, cable guide flanges.
• Deck Load Rollers: 6" SCH 160 pipe (6-5/8" OD) with double spherical
bearings, grease fittings, air operated to raise, spring load to lower,
used to assist in unloading skidded loads off the rear.
• Pin Pockets: 1 each side at rear on 45 degree angle with 1/2" grab
hooks, 2 each side in main deck inside outer beam, 7 each side on
outside of outer beam.
• D Rings: 15 on each side, outside of outer beam, 2 inside of neck.
• Outriggers: 11 each side, forged heavy duty, locking against beam and
at 90 degrees to beam
• Traction Cleats: 3/4" x 1" A514 T-1 steel, continuous welds solid on up
hilltop, intermittent welds on downhill side.
• Suspension: 30,000 lb. (per axle) air ride, air lift on front and rear axles,
manual dump all axles, travel limit straps on all axles.
• Axles: 5 -25,000 lb. round with outboard drums.
• Tires: 255R/70 x 22.5 Radial
• Brakes: 16 1/2 x 7, spring parking brakes on 4 axles, auto slack adjusters
• Bumper: 4" SCH 80 pipe with 4 -D rings
• Mud Flaps: Anti Sail
• Lights: Full DOT lights, sealed led lights.
• Coating: All surfaces near white metal steel grit blast, 2.5 ml profile
(SP-6), primed and color coated (before decking) with high solids
polyurethane, 4-6 ml dry film thickness.
Back