DRAGON DROP DECK CONTAINER Drop | Step Deck Trailers For Sale

Details

General Specs

DRAGON 60 x 102 Drop | Step Deck Trailers

Drop | Step Deck Trailers

Beaumont TX USA


General Specs

DROP DECK CONTAINER

New

60 ft

102 in

41.0 in

NOT SPECIFIED

5

120,000 lb


Body, Door, and Floor Specs

NOT SPECIFIED


Detailed Description

5 Axle Removable Neck Heavy Haul Trailer

Specifications:
• Type: Low Profile Flat Bed with removable neck.
• Payload: 60 tons (120,000 lbs.) distributed over
16 ft.
• Overall length: 59’ – 8”
• Deck length: 45’ – 0”
• Deck width: 8’ – 6” (102”)
• Deck height: 3’ – 5” (41”)

60 Ton 5 Axle Heavy Haul Trailer
• Deck Camber: 2” nominal, neck to tail
• King Pin Settings: 16” and 34”
• Swing Clearance: 8’ – 6’ (102”) and 10’ – 0” (120”)
• Frame: 4 beam design. Fabricated beams from a A514 T-1 high tensile steel flanges and
webs. Main beams boxed reinforced at critical deck transition, 2-1 minimum safety factor at
maximum payload stresses
• Front Deck: 22’ -8” L, 2” apitong attached at ends and every other cross member
• Rear Deck: 22’ -4” L including tail roller, 1/4” steel plate deck, continuous welds on top,
intermittent welds on under side
• Neck: Mechanical removable with roller at rear, 2 King Pin locations, spare tire carrier each
side
• Rear Deck Roller: 8” SCH 160 pipe (8 5/8” OD) with double spherical bearings, 2 sets of over
load rollers, grease fittings on main roller and overload rollers
• Neck Roller: 6” SCH 160 pipe (6-5/8” OD) with double spherical bearings, grease fittings,
cable guide flanges
• Deck Load Rollers: 6” sch 160 pipe (6-5/8” OD) with double spherical bearings, grease
fittings, air operated to raise, spring load to lower, used to assist in unloading skidded loads
off the rear
• Pin Pockets: 1 each side at rear on 45 degree angle with 1/2” grab hooks, 2 each side in main
deck inside outer beam, 7 each side on outside of outer beam
• D Rings: 15 on each side, outside of outer beam, 2 inside of neck
• Outriggers: 11 each side, forged heavy duty, locking against beam and at 90 degrees
to beam
• Traction Cleats: 3/4” x 1” A514 T-1 steel, continuous welds solid on up hilltop, intermittent
welds on downhill side
• Suspension: 30,000 lb (per axle) air ride, air lift on front and rear axles, manual dump all axles,
travel limit straps on all axles
• Axles: 5-25,000 lb. round with outboard drums
• Wheels: 10 hole steel disc hub pilot
• Tires: 255R/70 x 22.5 Radial
• Brakes: 16 1/2 x 7, spring parking brakes on 4 axles, auto slack adjusters
• Bumper: 4” SCH 80 pipe with 4 -d rings
• Mud Flaps: Anti Sail
• Lights: Full dot lights, sealed led lights
• Coating: All surfaces near white metal steel grit blast, 2.5 ml profile (SP-6), primed and color
coated (before decking) with high solids polyurethane, 4-6 ml dry film thickness
Back